Simultaneous improvement of thermal conductivity and mechanical properties for mechanically mixed ABS/h-BN composites by using small amounts of hyperbranched polymer additives

Recently, thermal interface materials (TIMs) are in great demands for modern electronics. For mechanically mixed polymer composite TIMs, the thermal conductivity and the mechanical properties are generally lower than expected values due to the sharply increased viscosity and poor filler dispersion. This work shows that addition of a small amount of polyester-based hyperbranched polymer (HBP) avoided the trade-off in mechanically mixed ABS/hexagonal boron nitride (h-BN) composites. After adding 0.5 wt% HBP, the maximum h-BN content in the composites increased from 50 to 60 wt%. The out-of-plane, in-plane thermal conductivity, and tensile strength of ABS/h-BN with 50 wt% h-BN were 0.408, 0.517 W/mK, and 18 MPa, respectively, and were increased to 0.729, 0.847 W/mK, and 32 MPa by adding 0.5 wt% HBP, while 0.972, 1.12 W/mK, and 29.5 MPa were achieved for ABS/h-BN/HBP with 60 wt% h-BN. The morphological and rheological results proved that these enhancements are due to the improved h-BN dispersion by decreasing viscosity of composites during mixing. Theoretical modeling based on the modified effective medium theory confirmed such results and showed that the interfacial thermal resistance also decreased slightly. Thus, this work demonstrates a facile and scalable method for simultaneously improving the thermal conductivity and mechanical properties of thermoplastic-based TIMs.     

Sintering behaviour of fluorapatite–silicate composites produced from natural fluorapatite and quartz

In this work, the sintering behaviour of fluorapatite (FAp)–silicate composites prepared by mixing variable amounts of natural quartz (2.5 wt% to 20 wt%) and FAp was studied. The composites were pressureless sintered in air at temperatures from 1000 °C to 1350 °C. The effects of temperatures on the densification, phase formation, chemical bonding and Vickers hardness of the composites were evaluated. All the samples exhibited mixed phase, comprising FAp and francolite as the major constituents along with some minor phases of cristobalite, wollastonite, dicalcium silicate and/or whitlockite dependent on the quartz content and sintering temperature. The composite containing 2.5 wt% quartz exhibited the best sintering properties. The highest bulk density of 3 g/cm³ and a Vickers hardness of >4.2 GPa were obtained for the 2.5 wt% quartz–FAp composite when sintered at 1100 °C. The addition of quartz was found to alter the microstructure of the composites, where it exhibited a rod-like morphology when sintered at 1000 °C and a regular rounded grain structure when sintered at 1350 °C. A wetted grain surface was observed for composites containing high quartz content and was believed to be associated with a transient liquid phase sintering.     

Mixed-Metal MOF-74 Templated Catalysts for Efficient Carbon Dioxide Capture and Methanation

The vast chemical and structural tunability of metal–organic frameworks (MOFs) are beginning to be harnessed as functional supports for catalytic nanoparticles spanning a range of applications. However, a lack of straightforward methods for producing nanoparticle-encapsulated MOFs as efficient heterogeneous catalysts limits their usage. Herein, a mixed-metal MOF, NiMg-MOF-74, is utilized as a template to disperse small Ni nanoclusters throughout the parent MOF. By exploiting the difference in Ni O and Mg O coordination bond strength, Ni²⁺ is selectively reduced to form highly dispersed Ni nanoclusters constrained by the parent MOF pore diameter, while Mg²⁺ remains coordinated in the framework. By varying the ratio of Ni to Mg in the parent MOF, accessible surface area and crystallinity can be tuned upon thermal treatment, influencing CO₂ adsorption capacity and hydrogenation selectivity. The resulting Ni nanoclusters prove to be an active catalyst for CO₂ methanation and are examined using extended X-ray absorption fine structure and X-ray photoelectron spectroscopy. By preserving a segment of the Mg²⁺-containing MOF framework, the composite system retains a portion of its CO₂ adsorption capacity while continuing to deliver catalytic activity. The approach is thus critical for designing materials that can bridge the gap between carbon capture and CO₂ utilization.     

Synthetic Peroxides Promote Apoptosis of Cancer Cells by Inhibiting P-Glycoprotein ABCB5

This article discloses a new horizon for the application of peroxides in medical chemistry. Stable cyclic peroxides are demonstrated to have cytotoxic activity against cancer cells; in addition a mechanism of cytotoxic action is proposed. Synthetic bridged 1,2,4,5-tetraoxanes and ozonides were effective against HepG2 cancer cells and some ozonides selectively targeted liver cancer cells (the selectivity indexes for compounds 11 b and 12 a are 8 and 5, respectively). In some cases, tetraoxanes and ozonides were more selective than paclitaxel, artemisinin, and artesunic acid. Annexin V flow-cytometry analysis revealed that the active ozonides 22 a and 23 a induced cell death of HepG2 by apoptosis. Further study showed that compounds 22 a and 23 a exhibited a strong inhibitory effect on P-glycoprotein (P-gp/ABCB5)-overexpressing HepG2 cancer cells. ABCB5 is a key player in the multidrug-resistant phenotype of liver cancer. Peroxides failed to demonstrate a direct correlation between oxidative potential and their biological activity. To our knowledge this is the first time that peroxide diastereoisomers have been found to show stereospecific antimalarial action against the chloroquine-sensitive 3D7 strain of Plasmodium falciparum. Stereoisomeric ozonide 12 b is 11 times more active than stereoisomeric ozonide 12 a (IC₅₀=5.81 vs 65.18 μm ). Current findings mean that ozonides merit further investigation as potential therapeutic agents for drug-resistant hepatocellular carcinoma.     

Control of reactive distillation production of high-purity isopropanol

The process characteristics and control strategy of a high-purity IPA reactive distillation column were investigated. A robust nominal operation was found by maintaining an excess of propylene feed to the column and recycling the unreacted propylene to the feed instead of the top stage. Stage temperature and propylene composition with one-to-one relationship with reboiler duty and propylene feed are selected as controlled variables for maintaining bottom purity and feed ratio in the presence of possible measurement bias respectively. High nonlinearity between selected input–output pair was reduced by using variable transformation. Dynamic simulations demonstrated that such a control scheme with nonlinear transformed variable was capable of providing much superior control performance than the one using natural variable.     

The method of double averaging: an approach for modeling power-factor-correction switching converters

This paper describes the modeling of power-factor-correction converters under average-current-mode control, which are widely used in switch-mode power supply applications. The objective is to identify stability boundaries in terms of major circuit parameters for facilitating design of such converters. The approach employs a double averaging procedure, which first applies the usual averaging over the switching period and subsequently applies generalized averaging over the mains period. The resulting model, after two averaging steps and application of a harmonic balance procedure, is nonlinear and capable of describing the low-frequency nonlinear dynamics of the system. The parameter ranges within which stable operation is guaranteed can be accurately and easily found using this model. Experimental measurements are provided for verification of the analytical results.     

High dynamic range InP HBT delta-sigma analog-to-digital converters

To date, the development of multifunction multicarrier digital receivers for cellular base station and military communications applications has been limited by the demanding dynamic range requirements for the analog-to-digital converter (ADC). The use of oversampling delta-sigma modulators provides a promising approach to overcoming the dynamic range barriers Nyquist-rate converters face in the same applications. This paper discusses issues involved in the design of high-speed high dynamic range wide-band delta-sigma ADCs for such communications applications. Test results of prototype designs are also presented. The delta-sigma modulators described in this paper operate at sampling frequencies ranging from 1 to 2.5 GHz with center frequencies ranging from dc to 100 MHz, providing between 74 and 84.2 dB signal-to-noise ratio (12 and 13.7 bits) for bandwidths of 25 and 12.5 MHz, respectively. The loop filters are continuous-time low-pass and bandpass implementations of order 6 and 10, and were fabricated in an InP heterojunction bipolar (HBT) technology. A typical tenth-order design consumes 6 W of power and occupies a die area of 23.5 mm/sup 2/.